Michell's range of sensors allow for measurements of dew-point, moisture content and trace moisture in both gases and liquids. From extremely dry parts-per-billion measurements (-120°Cdp) to high-humidity conditions with dew-points up to +60°C, our sensors are designed to reliably measure moisture in a wide range of applications. Our globally approved intrinsically safe and explosion-proof/flame-proof transmitters are available for use in hazardous areas.
Michell has 40 years of expertise in designing, manufacturing, and calibrating humidity & moisture sensors, moisture meters and other instrumentation, based on a range of technologies. We continuously invest in research to improve our moisture sensing technologies. This includes our range of dew-point transmitters, which are based on our widely used and field-proven ceramic impedance technology.
Dew-Point / Moisture in Pure Gases
Download Range Brochure
Accessories & services datasheet
As the largest manufacturer of dew-point transmitters in Europe, Michell Instruments has over 2000 transmitters under calibration at any moment in time, in our own production facility in Ely, UK, in addition to local calibration centres in Netherlands, France, Italy, Germany, China, Japan and USA.
Our manufacturing processes are optimized to meet high-volume ‘just in time’ agreements with major industrial equipment suppliers, and thousands of hygrometers leave our factory every month to measure and control moisture in some of the most demanding applications and locations around the world.
It is important all instruments are re-calibrated regularly to maintain accuracy and traceability. With Michell Instruments' unique Sensor Exchange Programme this can be achieved cost effectively and with virtually no down time. Simply request an exchange sensor from Michell or a local representative, then return your old sensor to us once you have removed and replaced it with the exchange sensor. All your calibration data is stored within the sensor, and each sensor comes with a traceable calibration certificate as standard.
Where Sensor calibration traceability is important, Michell offers an efficient recalibration service at our global service centres. Simply return the sensor to us, requesting the required calibration procedure and we will calibrate and return the sensor with a new traceable calibration certificate.
If our standard products don’t quite meet your requirements, our team of process engineers and systems designers can work with you to take your project from the design and consultation phase, right through to manufacturing and commissioning. Our 10 global sales and service centers in Americas, Europe, Middle East and Asia and our worldwide distributor network are always on hand to provide support for your challenging applications. Click here to get in touch today.
When warm compressed air leaves the compressor it will contain a high moisture content in the form of water vapour. Drying the air is important to prevent condensation forming in the distribution network, or at point of use.
Regenerative twin-column desiccant dryers are the most effective type of dryer. Measuring the dew-point at the dryer enables the columns to be switched-over only when performance in the active column starts to deteriorate, resulting in cost savings when air demand is low. This is known as dew-point dependent switching (DDS). More sophisticated DDS dryers also measure the inactive column to determine exactly when it has been regenerated, resulting in large savings in purge air and heating costs.
Measuring the amount of dissolved moisture dispersed throughout an immiscible process liquid is possible through the application of Henry’s Law. The transmitter calculates the moisture content using the measured water vapour pressure, saturation vapour pressure, and the user-entered saturation constant of the liquid.
High levels of water vapour in medical or breathing gases make them uncomfortable to breath and promote the growth of unwanted bacteria.
Pharmacological regulations state that the gases should periodically be tested to ensure that their dew point is sufficiently low.
More than 3 million vehicles world-wide are equipped to run on compressed natural gas, and the number of CNG filling stations is growing too. The ISO 15403:2000(E) states that ‘the single most important safety requirement of CNG fuel is a very low water dew-point to preclude the formation of liquid water at any time’.
For applications where keeping moisture levels as low as possible is of critical importance, sensitivity to (ppbV and ppmV) are required. Our advanced quartz crystal microbalance technology can help.
The applications for our dew-point transmitters are not limited to those listed on this page.
We have over 40 years experience measuring humidity & performing calibrations and can help you choose the best product for your application.